DRIZORO MAXSEAL FOUNDATION
MAXSEAL FOUNDATION is a cement based product which, with special additives and selected aggregates to provide total waterproofing protection to concrete, bricks and blocks due to its high resistance to aggressive waters. Will seal against positive and negative water pressure.
Waterproofing of retaining walls, car parks, basements, elevator pits, below grade ingress of water in foundations.It can also be used as waterproofing layer or barrier against humidity by capillarity on a variety of mortar substrates.
Will seal against positive and negative water pressure.
To obtain a good bond to concrete or masonry surfaces, it needs to be a medium to high porosity substrate. If low porosity MAXSEAL FLEX should be used. Remove all oils, loose materials as well as blooms or plaster to create a clean surface.
At the wall/floor junction, cut a 2x3 cm. slot, refill it with MAXREST Or MAXPLUG or MAXJOINT ELASTIC. If honeycombing is present in concrete, patch it with MAXREST.
Concrete scaffolding wires or passing rods must be cut and patch with a minimum 1 cm. deep must be made, then patch with MAXREST. IT IS THE RESPONSIBLITY of the applicator to determine whether a structure contains any form of efflorescence
buy 8 bags and get free delivery
Maxseal Foundation is a single component product used for waterproofing of below ground situations and negative water pressure. Suitable for application by brush.
MAXSEAL FOUNDATION is a construction grade cement based product which, together with special additives and selected aggregates gives it waterproofing characteristics, whether the foundations are in concrete or masonry. It gives great protection to foundation concrete due to its high resistance to aggressive waters
Can be rendered over or painted.
Can be rendered over 24 hours after second coat applied – flick or scratch coat must be applied by renderer – After 14 days can be painted over, normal paint procedure on any cement based coatings.
Any traces of efflorescence in negative waterproofing should be treated with Saltrid as per Efflorescence Specification. Concrete and masonry foundation walls subject to extreme pressures and water aggressiveness. Please contact office.
Pour clean water in a bucket and add MAXSEAL FOUNDATION, ratio approx 3.5kg powder to 1 litre of water mix slowly with electric drill (400-600 rpm) obtaining a thick creamy paste. Let material rest for 5 minutes before application. A 25 Kgs.MAXSEAL FOUNDATION bag requires 7-7.5 Itrs. of water.
At the joining area between vertical wall and foundation slab, make a 2x3 cm. slot refill it with MAXREST, MAXPLUG,MAXJOINT ELASTIC, MAXSEAL FLEX is recommendedfor all cold joints. If honey combing is present in concrete, patch with MAXREST. Dampen surface with clean water and apply a first MAXSEAL FOUNDATION layer with a 1,5 Kg / m2 load. After 14 to 24 hours curing, dampen the surface again before applying a second layer and must be applied crosswise with a 1 Kg / m2 load (1 to 1.5 mm wet film thickness)
Allow surface to cure for 3 days prior to back filling and 7 days prior to filling structure with water
During curing, water vapour may condense on the Surface in poorly ventilated areas. Place exhaust fan or heat source to eliminate moisture saturated air. Allow surface to cure for 3 days prior to back filling and 7 days prior to filling structure with water.
MAXSEAL FOUNDATION is applied by brush, MAXBRUSH or broom to ensure penetration into pores and hollows. Apply at a thickness of approx. 1 mm to form a continuous and even coating, do not extend as paint and apply only in one direction. Second layer must be applied crosswise. After material application, clean brushes with water for further use.
At summertime temperatures, wet the surface with abundant water to cool surface. If fast drying is observed, water can be mist sprayed 2 hours after the product application. In winter time do not apply at temperatures below 5º C or if lower temperatures are expected within the next 24 hours after the application.
It must not be applied on frozen or icy surfaces. Optimal working temperature is between 15 to 28º C. Avoid application when rainfall is expected within the next 4-6 hours further to application.
25 Kg., bags and 14 kg handipack.
One year in its original unopened container in a dry covered place, protected from frost.
Waterproofing and mechanical resistance.
Tests carried out at Instituto Eduardo Torroja, available upon request
As all cement products MAXSEAL FOUNDATION is an abrasive compound. It is not toxic but care should be taken while mixing and applying , do not to let it come into contact with the hands. Rubber gloves should be worn for protection. If it splashes in the eyes, rinse well with clean water; do not rub. If irritation persists, consult a doctor.
The information contained in this leaflet is based on our experience and technical knowledge, obtained through laboratory testing and from bibliographic material. DRIZORO reserves the right to introduce changes without prior price. Any use of this data beyond the purposes expressly specified in the leaflet will not be the Company ́s responsibility unless authorised by us.
The data shown on consumptions, measurement and yields are for guidance only and based on our experience. These data are subject to variation due to the specific atmospheric and jobsite conditions so reasonable variations from the data may be experienced. In order to know the real data, atest on the jobsite must be done, and it will be carried out under the client responsibility. We shall not accept responsibility exceeding the value of the purchased product.
For any other doubt, consult our Technical Department. This version of bulletin supersedes the previous bulletin.©