Duram Azcoseal is an extremely versatile product that seals, primes and protects. Applied to walls, Azcoseal provides a clear, wet-look, barrier against rain water ingress. Applied to porous floors Azcoseal is a glossy floor sealer against dust, dirt and spills. Azcoseal is an excellent primer for semi-porous substrates such as tilt up slabs requiring to be coated with acrylic paints and texture finishes.
DELIVERY ONLY $24 TO SYDNEY NEWCASTLE CANBERRA WOLLONGONG MELBOURNE BRISBANE ADELAIDE FOR ALL OTHER AREAS CONTACT US FOR PRICE
Azcoseal is a premium clear acrylic in a solvent solution. Azcoseal is formulated to provide a versatile sealer capable of deep
penetration into a wide range of substrate and cures to form a clean, tough (hard) and resilient coating in a satin (semi- gloss)
finish.
Azcoseal is an effective and long-lasting sealer against water penetration, wind driven rain and salt spray.
Azcoseal is also designed as a penetrative primer for subsequent water based and polyurethane waterproofing membranes and
high build paints and coatings and is particularly useful in high density and low-porosity surfaces such as tilt-up slabs.
Applied to pavers, brick, sandstone and masonry surfaces, Azcoseal gives an appealing 'wet-look' finish.
CAUTION: Sealed surfaces may be slippery when wet.
USES
Sealing and weatherproofing porous substrates such as face
brick against rain and salt spray.
• Providing a penetrative primer for water based and
polyurethane waterproofing membranes, high build paint
and architectural finishes on to porous substrates or over
existing painted surfaces.
• Encapsulating and sealing friable substrates such as
asbestos sheeting.
• Providing an attractive 'wet-look' sealer over pavers, brick,
sandstone and masonry surfaces.
• Reactivating existing acrylic coatings prior to recoating
SUITABLE SURFACES
Concrete
• Cement,
• Cement Render
• Block & Brickwork
• FC and CFC sheeting,
• Blue Board
• AAC, Hebel
• Composite sheeting
• Plywood
• Cement Pavers
• Sandstone
• Concrete Stencil
• Masonry Surfaces
• New& Old Acrylic coatings and membranes
• Vitreous, ceramic & Terra Cotta surfaces
Advice from Duram should be sort for the most appropriate priming method for these surfaces. Duram has a recommended
system for all the above.
*Note: Particle Board is not regarded as a suitable substrate for wet areas and particularly shower recesses and should be replaced
with CFC sheeting. As a minimum, Particle Board should be sealed with one to two coats of Duram Primeseal MC. All joins
and corners must be sealed with a polyurethane sealant and a reinforced fabric used in conjunction with the membrane. Surfaces
must be made good and should be sound, stable, dry, clean and free of dirt, dust and contaminants and suitably primed.
Test areas are highly recommended, particularly if coating pavers and terracotta tiles as solvents may dissolve entrapped
salts which may discolor the coating and tile.
• We strongly recommend that the user carries out testing and test patches prior to use as products and materials may vary.
• Is NOT recommended for particle board or chip board. Duram Primeseal MC is recommended for these surfaces.
• Is NOT a vapor barrier. For exposed areas such as roofs or where there is a risk of entrapped moisture in the surface
which can cause the membrane to bubble, Duram Primeseal MC should be used.
• It is NOT suitable for use on metal, some non-porous surfaces, shiny or very smooth concrete, glazed tiles, marble,
terrazzo, particle/chip board.
• Do not use on substrates where the membrane or what is adhered to the membrane is UV exposed. The preferred primer
for these areas is Duram Primeseal MC.
• Do Not use on substrates which contain high concentrations of moisture, over wet or seeping areas, saturated substrates,
and continual dampness.
• Is not a vapor barrier and should only be used when there is a low risk of entrapped moisture, the preferred primer for
these areas is Duram Primeseal MC.
• Cured coating may be slippery when wet.
• If area becomes wet before product has cured, it may turn product to a milky colour.
• Cured coating may be slippery when wet.
If used as a primer in exposed applications, ensure that solvents have fully evaporated before top coating. If not, there is a risk
that the topcoat may bubble
BENEFITS
Quick drying - usually within 1 hour, with a large extended top coating window
• Single component, easy to apply formula
• Designed to fill pores, bed down dust with excellent film forming properties
• Very economical & cost-effective process
• Dries tough and hard
• Low dirt pick up
• Provides a waterproof barrier against water ingress
• Minimises surfaces fragmentation as it has excellent binding properties
• UV Resistant, suitable for exposed areas.
• Dries clear with an attractive satin finish.
• When used as a primer it enhances the water proofing properties of the overall system.
• It incorporates cross- linking technology to enhance adhesion of the membrane ensuring a strong system bond to the
substrate.
• Enhances the overall performance and functionality of the waterproofing membrane.
• Has good strength, elasticity, and penetrative qualities.
• Improves the coverage and ease of application of the applied membrane.
• Suitable for use on most porous substrates.
• Low viscosity (modulus) for deep penetrating into the porous substrates
Follow all safety precautions as per product label and data sheet. Azcoseal contains solvent and is therefore flammable while still
wet. Ensure that all sources of ignition are kept well away. Ensure area is well ventilated. Adequate masks should be worn when
spraying. Protect surrounds against over spray. Observe all precautions on the Safety Data Sheet. In exposed areas, do not apply if
rain is imminent and protect coating from rain and inclement weather until fully cured.
Cured product may be slippery when wet.
APPLICATION
Azcoseal can be applied by brush, roller or spray, in 2 or more coats at the following minimum application rates (increase rates
for highly porous surfaces):
• As an encapsulating binder: Two coats at 4m² per litre per coat. Product should be worked well into the substrate.
• Clear weatherproof sealer: Two coats at 4m² per Lt per coat.
• As a primer: One coat at 4m² per Lt.
• Trafficable 'wet - look' finish: Three coats at 4m² per Lt per coat.
Allow each coat to dry before applying each additional coat. For best results apply subsequent coats within 24 hours of the
previous coat
COVERAGE
The stated average coverage rate may vary depending upon type, condition, porosity, texture of the surface and application
technique.
General coverage rate is 4m² per Lt per coat
DRYING
Drying and curing of the product is affected by type, dryness and porosity of the surface, temperature, humidity, ventilation,
climate conditions and application technique and therefore drying and curing can only be given as a guide.
At 25ºC and 50% RH (per coat):
• Touch dry: 1 to 2 hours
• Dry: 2 to 6 hours
• Full cure: Within 24 hours.
Service Temperature: 10ºC to 50ºC
Application Temperature: 5ºC to 30ºC
DELIVERY TO SYDNEY WOLLONGONG NEWCASTLE MELBOURNE BRISBANE AND ADELAIDE NO PO BOX
if you live outside these areas email us postcode for quote on delivery
PICK UP SYDNEY - EASTERN CREEK
QUEENSLAND - VIRGINIA
